4-fold 0-10 V actuator

The ekinex® 4-fold 0-10 V actuator EK-GF1-TP can be used as 0-10 V control output device or, alternatively, for controlling dimmerable LED power supply units.‎ When used for LED controlling, the selection of the colour can be made optionally in HSV or...

4-fold RGBW LED dimmer - Load current for each channel 4 A

4-fold KNX dimmer-actuator for switching and dimming of LED RGBW lighting devices. Mounting in distribution board on EN 60715 rail (4 modular units, each 18 mm). To be used in KNX installations for home and building automation.

Additional license for Tosibox® key with 1 mobile client

Additional license for Tosibox® key with 10 mobile client

Additional license for Tosibox® key with 5 mobile client

Binary input 8-fold

The ekinex® binary input EK-CA1-TP is a S-mode KNX modular device for rail mounting for connection to the bus of switches and sensors of conventional type (not communicating natively on the KNX bus) equipped with potential-free contacts. In this way, by...

Binary output 16-fold / blind actuator 8-fold

16-fold KNX binary output 16(10)A for switching and control of loads or 8-fold KNX actuator for control of drives for motorized blinds, shutters or curtains. Mounting in distribution board on EN 60715 rail (8 modular units, each 18 mm). To be used in KNX...

Binary output 4-fold

4-fold KNX binary output for switching and control of loads. Mounting in distribution board on EN 60715 rail (4 modular units, each 18 mm). To be used in KNX installations for home and building automation.

Binary output 8-fold

8-fold KNX binary output for switching and control of loads. Mounting in distribution board on EN 60715 rail (8 modular units, each 18 mm). To be used in KNX installations for home and building automation.

Binary output 8-fold / blind actuator 4-fold

8-fold KNX binary output 16(10)A for switching and control of loads or 4-fold KNX actuator for control of drives for motorized blinds, shutters or curtains. Mounting in distribution board on EN 60715 rail (4 modular units, each 18 mm). To be used in KNX...

Bus power supply 640 mA

KNX power supply 640 mA for a bus line. Mounting in distribution board on EN 60715 rail (4 modular units, each 18 mm). To be used in KNX installations for home and building automation.

Bus power supply 640 mA with auxiliary output 30 Vdc

KNX power supply 640 mA for a bus line. Mounting in distribution board on EN 60715 rail (4 modular units, each 18 mm). To be used in KNX installations for home and building automation.

Configurable logic module LM2

This module performs logic and data processing functions on data exchanged on the KNX bus. The device is powered by the KNX bus line with a SELV voltage 30 Vdc and does not require auxiliary power. Mounting in wall box or on 35 mm rail (EN 60715) with...

Current trasformer for interface EK-CF2-TP (5,20,30,40,50,60 A)

Current transformer (CT) to be used in combination with the load monitoring and control interface EK-CF2-TP. Available versions: EK-TA-05A (0...5 A); EK-TA-20A (0...20 A); EK-TA-30A (0...30 A); EK-TA-40A (0...40 A); EK-TA-50A (0...50 A); EK-TA-60A (0.....

Digital time/astronomical switch

KNX electronic digital switch for the management of electrical loads. It allows the time programming (daily, weekly, monthly or yearly) or astronomical. It allows to control 9 different channels on the KNX bus; the programming of channel 1 is also...

GPS Module for digital time/astronomical switch

GPS module able to capture the information of the date, time and geographical coordinates from the satellites that constitute the global positioning system (GPS) for use in combination with the digital time/astronomical switch EK-TM1-TP. The information...

Input/output module for hotel applications

Input/output module for office applications

The ekinex® actuators/controllers are input/output modules to manage all functions of either a hotel room (EK-HO1-TP), or an office or an open-space room: lighting, temperature control, shades and input/output indications. The device is equipped with...

Interface CF2 for load monitoring and control

Interface for load monitoring and control that can be used for: - the instantaneous current measurement absorbed by (up to) three single-phase electrical circuits or one three-phase electrical circuit; - the control of electrical loads with priority...

IP interface

IP interface for the connection of a PC or a laptop to a KNX bus installation through a LAN network. It supports the tunneling protocol. Mounting in distribution board on EN 60715 rail (2 modular units, each 18 mm). Powered by the bus line. To be used in...

IP Router

IP router for the connection of a PC or a laptop to a KNX bus installation through a LAN network. It supports the tunneling protocol. The bus coupler function allows to connect KNX TP bus lines through a TCP/IP backbone line. Mounting in distribution...

Line/area coupler

KNX line or area coupler for connecting a bus line with a secondary one. Mounting in distribution board on EN 60715 rail (2 modular units, each 18 mm). Powered by the bus line. To be used in KNX installations for home and building automation.

Mounting support for 35 mm din rail

Mounting support for 35 mm din rail - 5 pieces -

PLC CODESYS with KNX interface

The ekinex® EK-IA1-TP PLC allows to realize complex control and regulation logics for the automation of homes and buildings, integrating basic KNX functions.‎ The device is completely programmable by using the CODESYS* development environment...

Smart-U PLC (that features of an I/O PLC, Web HMI HTML5 and teleservice)

Remote control and monitoring unit that integrates in one device the features of an I/O PLC, Web HMI HTML5 and teleservice. SmartLab software development environment compliant with IEC 61131-3 (Programmable controllers - Part 3: Programming languages)...

Smart-U PLC with Ethernet port or Wi-Fi connection

Remote control and monitoring unit that integrates in one device the features of an I/O PLC, Web HMI HTML5 and teleservice. SmartLab software development environment compliant with IEC 61131-3 (Programmable controllers - Part 3: Programming languages)...

Spring fo hooking on E12 / E22 / E72 / ED2 / E32

Spring fo hooking on E12 / E22 / E72 / ED2 / E32 - 5 pieces -

Tosibox® key cryptographic micro controller (1 client PC + 1 mobile client)

Quickly and securely configurated VPN tunneling between PC and one or more Lock Routers and enables to generate activation codes for iOS and Android VPN client apps on smartphones. Connection authentication and encryption key exchange uses RSA 1024 bit...

Universal dimming actuator 2-fold

2-fold KNX dimmer-actuator for switching and dimming of lighting devices. Mounting in distribution board on EN 60715 rail (4 modular units, each 18 mm). To be used in KNX installations for home and building automation.

Universal interface (4 IN conf. As DI or NTC/4 OUT)with thermostat function

KNX bus device functioning as 4-channel input configurable for the connection of potential-free contacts or passive temperature sensors (NTC 10 kΩ at 25°C, to be ordered separately) and 4-channel output for control of low-consumption LED. Room thermostat...

Universal interface 2 IN/OUT

KNX bus device functioning as 2-channel input for the connection of potential-free contacts and 2-channel output for control of low-consumption LED.‎ Mounting in wall box or on 35 mm rail (EN 60715) with the support EK-SMG-35 (to be ordered separately).‎...

Universal interface 4 IN/OUT

KNX bus device functioning as 4-channel input for the connection of potential-free contacts and 4-channel output for control of low-consumption LED. Mounting in wall box or on 35 mm rail (EN 60715) with the support EK-SMG-35 (to be ordered separately)...

Universal interface CE2 (4 IN conf. / 2 OUT relais 5A)

KNX bus device functioning as 4-channel input for the connection of potential-free contacts (1 configurable for NTC temperature probe) and 2-channel output with 5A relais switching and control of loads. Mounting in wall box or on 35 mm rail (EN 60715)...

USB/KNX interface

Interface for the bidirectional data connection between a PC or laptop and a KNX bus installation. It enables addressing, parameter setting, visualization, protocolling and diagnosis of KNX bus devices through ETS (Engineering Tool Software). Mounting in...